Comments on: Finger joint router jig – one anyone can make http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/ Øyvind Nordhagen's blog Mon, 08 Mar 2010 08:46:02 +0000 http://wordpress.org/?v=2.9.2 hourly 1 By: admin http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/comment-page-1/#comment-206 admin Sun, 15 Mar 2009 10:46:01 +0000 http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/#comment-206 Thank you! To be honest, I haven't had the opportunity to try the jig out, although I have built it. So for now it's still based on a thought and I don't know if it will actually work in pratice. My Wordpress theme is K2, but I have customized it to some extent. Thank you! To be honest, I haven’t had the opportunity to try the jig out, although I have built it. So for now it’s still based on a thought and I don’t know if it will actually work in pratice.

My Wordpress theme is K2, but I have customized it to some extent.

]]> By: floor jack http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/comment-page-1/#comment-202 floor jack Sat, 14 Mar 2009 12:38:52 +0000 http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/#comment-202 I must say, I could not agree with you in 100%, but it's just my IMHO, which could be wrong. p.s. You have an awesome template . Where did you find it? I must say, I could not agree with you in 100%, but it’s just my IMHO, which could be wrong.
p.s. You have an awesome template . Where did you find it?

]]> By: admin http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/comment-page-1/#comment-151 admin Tue, 09 Dec 2008 23:00:23 +0000 http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/#comment-151 It can be clamped to a standard cheap-o woodworking table with an adjustable gutter in the middle. Clamp the jig to the table on only one of the movable pieces of the work top. The position the work pieces against the bottom of the cradle and fasten them by closing the gutter. Then clamp the other side of the jig to the table. What can I say.. It's what you get for not wanting to part with the $150 for a decent jig :) It can be clamped to a standard cheap-o woodworking table with an adjustable gutter in the middle. Clamp the jig to the table on only one of the movable pieces of the work top. The position the work pieces against the bottom of the cradle and fasten them by closing the gutter. Then clamp the other side of the jig to the table.

What can I say.. It’s what you get for not wanting to part with the $150 for a decent jig :)

]]> By: gael lopez http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/comment-page-1/#comment-150 gael lopez Tue, 09 Dec 2008 21:03:12 +0000 http://www.oyvindnordhagen.com/blog/2008/09/08/finger-joint-router-jig-one-anyone-can-make/#comment-150 HEY, QUIET GOOD I THINK, SIMPLE AND EFFICIENT , JUST ONE QUESTION HOW TO YOU SECURE THE JIG ON THE EDGE OF THE TWO UPSTANDING WOODBOARD... CLAMPS OR ONE SIDE OF THE JIG IS SLIDING ON SLOTS TOWARDS THE OPPOSITE ONE ???? GOOD ONE ANYWAY. GAEL HEY,

QUIET GOOD I THINK, SIMPLE AND EFFICIENT , JUST ONE QUESTION

HOW TO YOU SECURE THE JIG ON THE EDGE OF THE TWO UPSTANDING

WOODBOARD… CLAMPS OR ONE SIDE OF THE JIG IS SLIDING ON SLOTS

TOWARDS THE OPPOSITE ONE ???? GOOD ONE ANYWAY. GAEL

]]>